HCC570 ceramic hob
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Important
The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this
product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect
installation or misuse of the appliance or use in a commercial environment.
This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental
capacity, or who lack experience or knowledge about it, unless they have had supervision or instructions on how to use
the appliance by someone who is responsible for their safety.
Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified
personnel.
Appliance information:
Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a
fault with your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including
Electrical safety (LVD) 2006/95/EC and Electromagnetic interference compatibility (EMC) 2004/108/EC. Parts
intended to come into contact with food conform to 89/109/EC.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC
DIRECTIVE 2002/96/EC.
At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer
providing appliance recycling services.
Disposing of a household appliance separately avoids possible negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a crossed-out wheeled dustbin.
1
User information
Please note:
•
Ceramic hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been
allowed to cool.
•
•
Keep children away from the appliance when in use.
Never put cooking foil or plastic materials on the ceramic surface when the hob is hot. These materials could melt and
cause damage to the hob.
•
•
•
•
•
•
•
Never use the hob top for storage.
Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them.
Do not use pans with rough bases (e.g. cast iron) as these may scratch the hob surface.
Do not switch on the zones without cookware in place.
Do not lean over the hob when it is in use.
Follow the cleaning instructions carefully.
Ensure the base of the saucepan is clean and dry before placing it on the hob to prevent damage to the surface of the
hob.
•
•
After use, please ensure that the control knobs are in the ‘Off” position.
This hob (Class 3) has been designed for use only as a cooking appliance. Any other use (e.g. heating rooms) should be
considered incorrect and therefore dangerous.
•
The appliance is not intended to be operated by any means of an external timer or separate remote-control system.
Important
•
Do not use the hob if the glass surface is cracked or damaged to prevent risk of electric shock. Disconnect it from the
power supply.
2
Using your hob
Zones:
1.
Front left 1.7 kW 180 mm
2
2. Back left 1.2 kW 145 mm
3. Back right 1.7 kW 180 mm
4. Front right 1.2 kW 145 mm
3
Control panel:
5. Front right zone control
6. Back right zone control
1
4
7.
Back left zone control
8. Front left zone control
9. Residual heat indicator lights
10. Power indicator light
10
9
8
7
6
5
Fig.1
Residual heat indicator:
To warn when the zone is still hot after the power is switched off, the residual heat indicator will be lit for that zone.
Once the zone has cooled down to a safe temperature, the residual heat indicator will switch off.
Regulating the temperature:
The power level for each zone can be regulated by turning the relevant control knob to select the desired heat level.
The table below offers guidance as to what each switch position is for.
Heat setting
Description
1
2
3
4
5
6
Very gentle
Gentle
Slow
The ‘OFF’ position is indicated by the symbol ‘0’.
The indicator will light when the hotplate is in use.
When you have finished cooking, check to ensure that the zones are
switched off and the indicator is not lit.
Medium
High
Very high
3
Efficient Use of your Hob
The hob is equipped with zones of different sizes, designed to accommodate most shapes and sizes of pan. For best
results, only use pans with flat bottoms and choose an appropriate zones depending on the size of the pan. The most
efficient use of the hob is shown below, where the pan and zones are correctly chosen.
Use pan lids where possible to minimize the energy usage of your appliance.
Turn off each zone a few minutes before the end of cooking time. The residual heat in the zones will continue to cook the
food for the remaining cooking time.
Fig.2
Zone Size
145mm
Minimum Pan Size (cm)
Maximum Pan Size (cm)
12
16
16
20
180mm
It is very important that the pans used on the hob are made of a suitable material and have the correct type of base. The
base should be flat and smooth, as any rough part on the pan base could scratch the ceramic hob top.
Choose pans which are between the sizes recommended in the table above, and with bases that are as non-reflective as pos-
sible, e.g. dull and dark.
Only pans recommended for use on ceramic hobs should be used.
4
Care and Maintenance
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.
You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and
could erase the control panel markings.
Types of residues
Clean with
Cleaning advice
Wipe over the zone to be cleaned with a sponge and hot
water, and then wipe off with a soft dry cloth.
Light
Cleaning sponge and soft cloth
Wipe over the zone to be cleaned with a sponge and hot
water, using a ceramic scraper to remove any large marks
or stains and then wipe off with a soft dry cloth.
Accumulated baked-on stains/
dirt, sugar spills or melted plastics
Cleaning sponge or glass scraper
and soft cloth
Pour a small amount of warm white vinegar onto the stain,
leave it to stand, and then wipe off with a soft dry cloth.
Rings and hard water residues
White vinegar and soft cloth
fast frying steaks
9
Important:
•
Steam cleaners must not be used when cleaning this appliance.
Mains electrical voltage:
230 – 240Vac, 50 Hz
5.8 kW
Total rated electrical consumption:
If your Hob is not working:
1. Check that the control knobs are switched on.
2. Check that the mains supply has not been switched off.
3. Check that the fuse in the consumer unit has not blown.
5
Mains Electricity Connection
Warning! This appliance must be earthed
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who
will comply with the I.E.E. and local regulations.
This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or
13A supply.
This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at
least 3mm in all poles. The switch must be positioned no further than 2m from the appliance.
Please note:
•
This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5 mm2. A larger
cable may not fit the terminal connections.
•
The marking of the current rating of the fuse or circuit breaker protecting this appliance should be marked on the
socket outlet.
•
•
Assembly and electrical connection should be carried out by specialised personnel.
When installing this product we recommend you seek the help of another individual.
link wire
Use a 32A fuse breaker
Fig.3
6
Fitting the Hob
Unpacking the hob:
•
Take care not to lose or mishandle any parts.
Fitting position of the hob:
This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any
adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant
to fire (tiles or steel, for example). These dimensions are shown in Fig.4.
If fitting a cooker hood above the hob:
If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is
recommended) (Fig.5). If the instructions supplied with the hood dictate that the hood must be installed at a height greater
than 600mm, then that height is the minimum required.
Wall furniture requirements:
The minimum height of any cabinet immediately above the hob is 900mm. The minimum height of any adjacent units
(including light pelmets) is 400mm, unless they are manufactured from a material resistant to fire (steel, for example)
Notes:
•
•
Do not position this appliance above a refrigeration unit. The heat generated may cause the refrigeration unit to fail.
This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C or greater above
ambient temperature.
•
•
If there is no oven to be built in below the hob, an isolation shelf should be fitted to protect the user from high
temperatures. If the hob is to be installed above a working drawer, then a partition should be fitted to protect the contents
and user from the heat generated during use. This should be fitted 100mm below the hob.
Never place perishable foods in the cupboard below the appliance.
7
How to Install the Hob
How to install the hob:
Overall dimensions of the hob: Width: 580mm
Depth: 510mm
Depth: 490mm
Worktop cut-out dimensions:
Width: 560mm
1. Make the required hole in the worktop. Note that before doing this, check the instructions supplied with any cooker hood
to ensure that you will have the required clearance. The cut-out (Fig 4) shows a 61.5mm gap from the wall to the cut-out
edge. The distance for the hob, when fitted, to the back wall is 50mm.
2. Position the hob seal, as shown in the diagram below (Fig 6), ensuring that the ends meet without overlapping. Do not use
silicone type sealant.
3. Secure the hob to the worktop using the fixing brackets and screws supplied, as shown in the following diagram (Fig 7).
Remove any excess sealant after tightening the brackets.
>60mm
490mm
560mm
1
190mm
190mm
Fig.4
Fig.5
3cm
4cm
Fig.6
Fig.7
8
9
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
|