1353/1361-1
Module No.1353/1361
GENERAL GUIDE
•
•
Press C to change from mode to mode.
If the digital display of your watch is continually changing, see “Auto Display function” for information on how to stop it.
Reminder Mode
Telememo Mode
Schedule Memo Mode
1361
C
C
C
Timekeeping Mode
A
B
A
A
C
B
D
C
C
D
Hand Setting Mode
Stopwatch Mode
Alarm Mode
The operational procedures for
modules 1353 and 1361 are iden-
tical. All of the illustrations in this
manual show module 1353.
C
C
C
About icons
TIMEKEEPING MODE
The following table shows the icons used by this watch.
Meaning
Don't forget!
Note
For the sake of simplicity, the sample displays in this manual do not show the analog
hands of the watch.
Meaning
Icon
Icon
Telephone call
About the Timekeeping Mode display
Press D to change the display format in the Timekeeping Mode as shown below.
Meeting
Gift/Anniversary
Documentation
Dining
Format 1
Format 2
Format 3
Travel
A
B
Payment/Receipt
Sports
C
D
Music
Day of the
week
Date
Hour
Minutes
Seconds
Hour hand
Month
Minute hand
To turn an icon on and off
The following describes the icons that are shown in Format 1 and Format 2 displays.
1. Make sure that the watch is in the Reminder Mode.
If not, use Cto enter the Reminder Mode.
•
•
All icons that are turned on in the Reminder Mode.
ON/OFF
A
B
All icons that are turned on for appointments registered in the Schedule Memo Mode
for the current date. The icon of the next appointment flashes on the display. Icons
automatically disappear from the display when the time for the appointment expires.
For details on schedules and reminders, see the sections of this manual covering the
Reminder Mode and Schedule Memo Mode.
2. Press D and the
icon flashes at high speed on
the display because it is currently selected. Also,
any icons that are turned on flash, at a somewhat
slower speed.
A
•
3. Use D to select the icon you want. Each press of
C
D
D
moves the high-speed flashing (selection) in
To set the time and date
the following sequence.
On/off status
1. Make sure that the watch is in the Timekeeping Mode. If not, use C to enter the
Timekeeping Mode.
2. Hold down A while in the Timekeeping Mode until the seconds digits start to flash
on the display. The seconds digits flash because they are selected.
3. Press Cto change the selection in the following sequence.
The high speed flashing stops
Seconds
Date
Hour
Minutes
Year
•
The on/off status of the selected icon is shown on the display as “On” and “OFF”.
12/24-hour
format
4. Press B to turn an icon on and off.
5. Repeat steps 3 and 4 to turn other icons on and off.
Month
6. Press C to exit the Reminder Mode.
4. While the seconds digits are selected (flashing), press D to reset the seconds to
“00”. If you press D while the seconds count is in the range of 30 to 59, the seconds
are reset to “00” and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
•
The following shows how the display automatically changes if you do not operate
any button for a few minutes while in the Reminder Mode.
5. While any other digits (besides seconds) are selected (flashing), press Dto increase
the number or B to decrease it. Holding down either button changes the current
number at high speed.
While the 12/24-hour setting is selected, press B or D to switch between two
formats.
Reminder icon selected
(high-speed flashing)
Normal Reminder Mode
(high-speed flashing stops)
Timekeeping
Mode
A few
minutes
A few
minutes
6. After you set the time and date, press A to return to the normal Timekeeping Mode
(the flashing stops).
To turn all Reminder Mode icons off
In the Reminder Mode, press B and D at the same time to turn all Reminder Mode
icons off.
•
•
•
The day of the week is automatically set in accordance with the date.
The date can be set within the range of January 1, 1995 to December 31, 2039.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the normal Timekeeping Mode automati-
cally.
TELEMEMO MODE
Day of the week abbreviations
The Telememo Mode lets you store up to 50* pairs of name and telephone number
data. The name can be up to 8 characters long and the numbers 12 digits each. Data
is automatically sorted into alphabetical order based on the name data. You can recall
data by scrolling through a sorted list.
* The Telememo Mode shares memory with the Schedule Memo Mode. This means
that the maximum number of Telememo Mode entries you can store is reduced each
time you store data in the Schedule Memo Mode.
Day of the week is displayed as shown below.
SUN : Sunday
WED : Wednesday
SAT : Saturday
MON : Monday
THU : Thursday
TUE : Tuesday
FRI : Friday
About the Reminder signal
To input Telememo data
Whenever reminder icons are turned on (see “Reminder Mode” for details), all turned
on icons and current time appear on the display for about 20 seconds every hour on the
hour, regardless of what display format the watch is in.
Name
A
B
Mode
indicator
REMINDER MODE
This icon is turned on
C
D
Telephone number
Use the Reminder Mode to turn on icons that help
Number of items in memory
you remember things you have to do. Any reminder
icon you turn on in the Reminder Mode appears on
the Timekeeping Mode’s display format 1 and 2 (see
Remaining memory capacity (number of items)
A
B
“About the Timekeeping Mode display”).
1. Make sure that the watch is in the Telememo Mode. If not, use C to enter the
A
•
Whenever you enter the Reminder Mode, all of the
available icons appear. The icons that are turned
on flash.
Telememo Mode.
•
Whenever you enter the Telememo Mode, the display shows how many items are
already stored in memory and how many items you can input before memory becomes
full. After a few seconds, the display changes to show the item that was selected
when you last exited the Telememo Mode.
C
D
Mode indicator
Current date
Current time
1353/1361-3
To delete a specific Schedule Memo item
To time first and second place finishes
1. In the Schedule Memo Mode, use B or D to scroll through the data items and
display the one you want to delete.
1. Press Dto start the stopwatch.
2. Press Bwhen the first finisher crosses the line, and record the time.
2. Press A and the month digits begin to flash because they are selected.
3. Press B and D at the same time. The watch beeps and the message “
appears on the display, indicating that the item is deleted. At this time, the cursor
appear on the display, ready for input.
3. Press Dwhen the second finisher crosses the line.
4. Press Bto display the finishing time of the second finisher.
5. Press Bagain to clear the stopwatch to all zeros.
”
4. Input data or press A to return to the normal Schedule Memo Mode (the flashing
stops).
HAND SETTING MODE
Hour hand
When the time shown on the display does not match
the analog setting, use this mode to correct this situa-
tion by changing the analog setting.
Minute hand
ALARM MODE
When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset
time each day. Press any button to stop the alarm after it starts to sound. When the
Hourly Time Signal is switched on, the watch beeps every hour on the hour.
Note that the Daily Alarm and the Hourly Time Signal operate based on the digital time
setting.
A
B
To set the analog time
1. Make sure that the watch is in the Hand Setting
Mode. If not, use C to enter the Hand Setting
Mode.
C
D
2. Hold down A while in the Hand Setting Mode until
To set the alarm time
the indicator “
play.
” starts to flash on the dis-
Current time
Current date
1. Make sure that the watch is in the Alarm Mode. If
not, use Cto enter the Alarm Mode.
Alarm on indicator
Mode
indicator
ON/OFF
2. Hold down A while in the Alarm Mode until the
hour digits start to flash on the display. The hour
digits flash because they are selected. At this
time the Daily Alarm is switched on automatically.
A
C
B
D
3. Press Dto advance the hands of the analog timepiece.
4. After you set the analog time, press A to return to the normal Hand Setting Mode
(the flashing stops).
The following shows how the display automatically changes if you do not operate
any button for a few minutes while in the Hand Setting Mode.
•
Hourly Time Signal on
indicator
Mode
indicator
Hour
Minutes
Hand time setting
(the indicator flashes)
Normal Hand Setting Mode
(the flashing stops)
Timekeeping
Mode
A few
minutes
A few
minutes
3. Press C to change the selection in the following sequence.
Hour
Minutes
ABOUT THE MODULE 1361 DISPLAY
4. Press D to increase the selected digits and B to decrease them. Holding down
either button changes the number at high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (indicated as “ ” on the display).
The following shows how the display of module 1361 changes for about 20 seconds
when a Reminder signal sounds.
•
•
5. After you set the alarm time, press A to return to the normal Alarm Mode (the
flashing stops).
The following shows how the display automatically changes if you do not operate any
button for a few minutes while in the Alarm Mode.
Normal display
Reminder signal display
Alarm time setting
(Flashing)
Normal Alarm Mode
(No flashing)
Timekeeping
Mode
A few
minutes
A few
minutes
•
The display changes similarly when a Schedule Memo signal sounds, or when a
daily alarm sounds in the Timekeeping Mode. When a Schedule Memo signal
sounds, time of the nearest scheduled appointment appears, instead of the current
time.
To switch the Daily Alarm and Hourly Time Signal on and off
Press B while in the normal Alarm Mode (when no digit is flashing) to change the
status of the Daily Alarm and Hourly Time Signal in the following sequence.
AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually changes the contents of the digital
display. Note that you cannot use any of the watch’s other function while the Auto
Display function is operating.
Daily Alarm
only
Hourly Time
Signal only
Both on
Both off
To stop the alarm
To turn the Auto Display on
Press any button to stop the alarm after it starts to sound.
A
B
D
Hold down C for about three seconds in any mode
until the watch beeps.
To test the alarm and select an alarm tone
To turn the Auto Display off
1. Hold down Dwhile in the normal Alarm Mode to sound the alarm.
2. While holding down D, press B to switch between the three available alarm tones.
The last alarm tone that is sounding is selected when you release D.
C
Hold down C for about three seconds until the watch
beeps. At this time, the watch is in the Timekeeping
Mode.
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other settings are flashing on the display).
STOPWATCH MODE
Mode indicator
The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes. The range of the stop-
watch is 23 hours, 59 minutes, 59.99 seconds.
SPLIT/RESET
A
C
B
D
To measure elapsed time
1. Press Dto start the stopwatch.
2. Press Dto stop the stopwatch.
•
You can resume the measurement operation by
pressing Dagain.
START/STOP
3. Press Bto clear the stopwatch to all zeros.
Hours
1/100 second
Minutes
Seconds
To record split times
1. Press D to start the stopwatch.
2. Press Bto display the timing up to that point. Stopwatch timing continues internally.
•
At this time, the display also changes from “
split time is being recorded.
” to “
”, indicating that the
•
Split time is cleared if you exit the Stopwatch Mode during the timing operation.
3. Press B to clear the split time and to continue time measurement on the display.
You can repeat steps 2 and 3 as many times as you want.
•
4. Press D to stop the time measurement.
5. Press B to clear the stopwatch to all zeros.
|