ENG
®
11
MICRO Wireless
CYCLOCOMPUTER
CC - MC100W
Owner’s Manual
Max.
Distance
U.S. Pat. Nos. 4633216/4636769/4642606/5236759 and Design Pat. Pending
Copyright© 2004 CAT EYE Co., Ltd.
CCMC1W-041129 066600370 2
70 cm
1
2
4
5
Component name
1 Bracket
2 Speed Sensor A
3 Magnet
4 Bracket Rubber Pad
5 Sensor Rubber Pad
6 Nylon Ties (L x2)
7 Nylon Ties (S x2)
8 Double-sided tape
33
22
6
7
3
8
1
8
1
8
1
7
or
1
4
1
7
5
2
2
3
3
6
2
SENSOR ZONE
A
2
B
5 mm
SENSOR
ZONE
3
2
3
1
Troubleshooting
No display.
Is battery in the computer run down?
Replace it, and re-enter the correct information. (All Clear ).
CAUTION
Standard Parts
• Do not concentrate on the computer while riding. Be sure to
ride safely!
ENG
• Install the magnet, sensor, and bracket securely. Check these
periodically.
a
#169-6590
Incorrect data appears.
Parts Kit
• Dispose of used batteries according to local regulations. If swal-
lowed, consult a doctor immediately.
Do all clear operation. (All Clear
Pressing the START/STOP button does not calculate Elapsed Time.
Is the icon illuminated?
To start/stop measurement using the START/STOP button, turn off
Auto-mode.
The sensor signal icon does not flash. (The speed is not displayed.)
[If the signal icon does not flash, reduce the distance between the sensor
and computer, adjust the position of the magnet, and spin the wheel again.
If the icon now flashes, this indicates that the computer and sensor are
too far apart or that the battery is low.]
Is the clearance between the sensor and magnet too great?
Does the magnet pass through the sensor zone?
Adjust the positions of the magnet and sensor.
a
).
• Avoid having the computer in hot direct sunlight for extended
periods.
• Do not disassemble the computer.
• Clean the computer and accessories with a soft cloth damp-
ened with a neutral detergent. Do not use thinners, benzene, or
alcohol on the computer.
#169-6580
Wireless Sensor
Speed Sensor A
The sensor was designed to receive signals within a limited range to
prevent sensor signal interference. Thus, the sensor and computer
must be relatively close. If the temperature or battery power is low,
they may need to be even closer than normal. The sensor must be
installed at the top of the fork, and the distance between the sensor
and the computer should not exceed approximately 70 cm. Install
the computer on the stem, with its bottom surface facing the sensor.
(Take into account the angle of the stem.)
Is the computer installed at the correct angle?
Install the computer with its bottom surface facing the sensor.
#169-6570
Is the distance between the computer and sensor too great?
Install the sensor closer to the computer.
Is the sensor battery weak?
In winter, battery performance degrades.
Replace it.
Bracket kit
Interference may occur, resulting in malfunction, if the computer is:
• Near a TV, PC, radio, motor, or in a car or train.
• Close to a railroad crossing, railway tracks, TV stations and or
radar base.
Is the computer’s battery weak?
Replace it with a new one. (All Clear
• Close to a second bicycle with wireless sensors.
#169-9691
a
).
Correct installation of sensor and magnet
Attach the magnet 3 so that it passes through the sensor
zone of the sensor 2.
Be sure to have a 5 mm-or-less clearance between the sensor
2 and magnet 3.
Part names
Current Speed
Sensor signal reception icon
Flashes in sync with sensor signals.
Sub measurement icon
Wheel Magnet
Replacing the Battery
• Computer
If the Wheel Size icon (
A
B
or
) flashes, replace the battery.
The Total Distance can be entered manually. Before removing
the battery, note the current Total Distance. Install a new lithium
battery (CR2032) with the (+) side facing upward.
Then re-start the computer according to the SETTING proce-
dure, and then set the clock from the MENU FLOW.
• Sensor
#166-5150
Lithium Battery (CR2032)
A
B
C
D
If sensor reception is poor, replace the battery. Then check the
positions of the battery and magnet.
Pace arrow
Option Parts
Indicates whether the current speed is faster or slower than
the average speed. ( Faster Slower)
Auto mode icon
Specification
Battery ............. Computer: Lithium Battery CR2032 X 1
Sensor: Lithium Battery CR2032 X 1
E
F
#169-6667
Battery Life ...... Computer: approx. 1 year (If the computer is used for
1 hour/day without the backlight on)
Speed unit
Center Mount Kit
b
G
Mode symbol ....................................................................
Sensor: until Total Distance reaches about 10,000 km
(6,250 mile)
Indicates the mode currently selected.
Tm (Tm 2) ............... [Elapsed Time]
Dst (Dst 2) ............... [Trip Distance]
Av (Av 2) .................. [Average Speed]
Mx ............................ [Maximum Speed]
Odo .......................... [Total Distance]
............................ [Clock]
*This is the average figure of being used under 20°C temperature and
the dis tance between the computer and the sensor is 65 cm.
* If the backlight is used frequently, the battery life diminishes accordingly.
Controller .......................... 4-bit 1-chip microcomputer
(crystal controlled oscillator)
#169-9760
Display ............................... Liquid crystal display
Sensor ............................... No contact magnetic sensor
Wheel Circumference Range ....... 0100 mm - 3999 mm
(default figure A : 2095 mm, B : 2050 mm)
Working Temperature ....... 0°C - 40°C (32°F - 104°F)
Dimension/Weight
Magnet for Composite Wheel
H
I
J
Wheel size icon
Backlight button
Battery Case Cover
52.5 x 38 x 22 mm [2-3/32" x 1-1/2" x 7/8"]
/ 30 g [1.06 oz]
Starting/Stopping measurement
This computer allows automatic (Auto-mode) or manual measurement.
During measurement, the speed unit icon flashes. The maximum
speed and total distance will update, regardless of measurement.
• Auto-mode (automatic measurement)
* The factory-loaded battery life might be shorter than the above-men-
tioned specification.
* The specifications and design are subject to change without notice.
#169-9690
Hi-Power Wheel Magnet
If the
icon is visible, measurement is automatic.
In Auto-mode, starting/stopping measurement using the START/
STOP button is impossible.
• Manual measurement
If the
icon does not light, starting/stopping the measure-
ment using the START/STOP button is possible.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Modifications The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by CatEye Co., Ltd. May void the user’s
authority to operate the equipment.
* Use the menu screen to toggle between Auto-mode ON and
OFF. For further information, see the MENU FLOW.
Switching Mode symbol ....................................
b
Press the MODE button to switch measurement according to the
OPERATION FLOW.
Press the MODE button for 2 seconds to switch from Main to Sub
measurement.
LIMITED WARRANTY - 2-Year Computer/Sensor only
(Accessories/Attachments and Battery Consumption excluded)
• Sub measurement
If trouble occurs during normal use, the part of the Main Unit or sensor will be repaired or
replaced free of charge. The service must be performed by CatEye Co., Ltd. To return the prod-
uct, pack it carefully and remember to enclose the warranty certificate with instruction for repair.
Please write or type your name and address clearly on the warranty certificate. Insurance, han-
dling and transportation charges to our service shall be borne by person desiring service.
When Main measurement starts/stops, Sub measurement starts/
stops accordingly. Note, however, that the main and sub mea-
surements must be reset individually.
Resetting Main and Sub measurement at different times allows
interval measurement to be carried out.
* In the sub measurement the pace arrow compares the current
speed to average speed 2.
Service & Research Address for USA
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-
CATEYE Service and Research Center
c
d
Resetting data ........................... Main :
Sub :
1705 14th St. 115 Boulder, CO 80302
To reset measurement data, display the Main/Sub measurement
data and press the START/STOP and MODE buttons simulta-
neously. Trip distance is not reset.
ku, Osaka 546-0041 Japan
Phone: 303.443.4595
Attn: CATEYE Customer Service Section
Toll Free: 800.5CATEYE
Fax: 303.473.0006
E-mail: [email protected]
Backlight
Press the backlight button to illuminate the display for 3 seconds.
If the battery is low, the wheel size icon flashes and the display
does not illuminate.
Power-saving function
If the computer has not received a signal for 10 minutes, power-
saving mode will activate and only the clock will be displayed. When
the computer receives a sensor signal again, the measuring screen
reappears. If two weeks’ inactivity elapses, power-saving mode will
change to SLEEP mode. Pressing the MODE or START/STOP but-
ton in SLEEP mode brings up the measuring screen.
Dual Wheel Size
Two wheel sizes (Wheel sizes
and
) can be registered on
the computer. This is useful when the computer is shared be-
tween two bicycles or when one bicycle uses different wheel sizes
at different times. Wheel size B has pre-programmed for a 26x1.95"
size tire.
* Use the menu screen to toggle between
ther information, see the MENU FLOW.
and
. For fur-
Changing the computer settings
If the MENU button is pressed with the measuring screen dis-
played, the menu screen appears. Press the START/STOP button
when measurement has stopped and no signal is being received
to change menu settings.
• Setting the clock
Set the clock via
Settings in the MENU FLOW.
* For the Speed unit, reset Main and Sub measurement data
before changing settings.
* For further information, see the MENU FLOW.
Maintenance
To clean the computer or accessories, use diluted neutral deter-
gent on a soft cloth, and then wipe it off with a dry cloth.
3
|