Chauvet Work Light TFX FS360 User Manual

READ FIRST!

TFX-FS360

Followspot™ 400G

To start using as a Followspot,

press the FUNCTION button until

the Manual LED turns on.

Ask your dealer about

the specially designed

tripod stand with

casters for the TFX-

FS360.

Model Number

CH-W28

USER MANUAL

5200 NW 108^thAve Sunrise, FL 33351

(800) 762-1084 – (954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

2010-07-20/14:53

BEFORE YOU BEGIN

What is included



1x TFX-FS360

1x Single gobo-slot with 4 free gobos

1x Power cord with plug



1x ENX lamp (360 W, 82 V)

1x User Manual

1x Warranty Card

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specification. A fixture’s listed current rating is its average current

draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot

be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is

used solely for a 0% to 100% switch. Before applying power to a fixture,

AC Voltage Switch

check that the source voltage matches the fixture’s requirement. Check the

fixture or device carefully to make sure that if a voltage selection switch

exists that it is set to the correct line voltage you will use.

Warning!

Verify that the power select switch on your unit matches the line

voltage applied. All fixtures must be connected to circuits with a

suitable Ground.

Safety Instructions

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?



Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.



Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

Don’t connect the device to a dimmer pack.

Make sure power cord is never crimped or damaged.

Never disconnect power cord by pulling or tugging on the

cord.

Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

This product is intended for indoor use only!

To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

The unit must be installed in a location with adequate

ventilation, at least 50 cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.



Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.



Avoid direct eye exposure to lamp while it is on.

Caution!

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs

yourself. In the unlikely event your unit may require service, please contact CHAUVET®.

TFX-FS360 User Manual

2010-07-20/14:53

INTRODUCTION

Features



2-channel DMX-512 followspot

7 dichroic colors + white: (red, blue, green, yellow, orange, magenta, UV purple)

Variable electronic dimmer (0-100%)

Variable mechanical iris

Variable mechanical focus

Additional Features



Followspot stand (CH-W28)

Options



Single gobo slot with 4 free gobos

DMX Channel Summary

CHANNEL

FUNCTION

Color

Dimmer

Product Overview

Lamp access

Control panel

Iris

Gobo-holder

Located and inserted on

the bottom side of the

followspot.

Focus

Yoke

Gobos included

Control panel

DMX

Input/Output

Optional

CH-W28 Tripod

w/casters

Focus handles

TFX-FS360 User Manual

2010-07-20/14:53

SETUP

Lamp

You will need to install a lamp prior to the initial operation of the fixture. An ENX, 360 W halogen lamp

is included.

Warning!

When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool

down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp

with alcohol and wipe it with a lint free cloth before installation.

LAMP INSTALLATION

Lamp Installation

1) Remove screw located on the top and to the rear of

Remove screw

the followspot as pictured on the right.

2) Open lamp cover until lamp compartment is exposed.

3) If replacing the lamp, remove old lamp first.

4) Reach in and slide the lamp out of the retaining cage.

5) Detach the lamp from the lamp socket and replace.

6) Replace lamp cover, align the screw hole and fasten

the screw.

7) No lamp alignment is necessary for this fixture since

the lamp is already optimized inside the reflector.

Lamp exposed

Power

Warning!

Verify that the power on your unit matches the line voltage applied. All fixtures must be

connected to circuits with a suitable Ground.



To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart.



A fixture’s listed current rating is its average current draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable

resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch.



Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.

All fixtures must be connected to circuits with a suitable Ground.

Gobo Holder

The TFX-FS360 can project one gobo image. A gobo-

holder is included and is located directly underneath the

followspot next to the fan as pictured here on the right.

Remove the two bottom screws from the gobo-holder

and slide it out. You can remove the gobo by sliding it

out the top and replacing it with a different one or

replace gobo-holder without a gobo for followspot only use.

TFX-FS360 User Manual

2010-07-20/14:53

Mounting

ORIENTATION

This fixture may be mounted in any safe, position provided there is adequate room for ventilation.

STATIC MOUNT

Hanging Clamp

The TFX-FS360 comes equipped with a yoke for pipe clamp

installations. The yoke will provide for a static mount or installation of

the followspot for pre-focused use. It is important never to obstruct the

fan or vents pathway. Mount the fixture using, a suitable “C” or “O”

type clamp. Adjust the angle of the fixture by loosening both knobs

and tilting the fixture. After finding the desired position, retighten both

knobs.

Note!

Clamp is sold separately.



When selecting installation location, take into consideration lamp

replacement access and routine maintenance.



Safety cables should always be used.

Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature

changes or restricted ventilation.

TRIPOD STAND WITH CASTERS CH-W28 (OPTIONAL)

The CH-W28 is a multipurpose followspot/speaker stand with casters. Assemble tripod for use with

casters as indicated in the CH-W28 manual.

Yoke

1. Mount yoke bracket so the bracket side

runs across the bottom.

2. Mount the followspot bracket onto the

tripod mounting plate

3. Align screw holes with mounting plate

openings and fasten with supplied bolts.

Mounting plate

Please visit your participating dealer and ask

for the CH-W28 Tripod from CHAUVET®. To

locate a dealer near you contact CHAUVET®

at (954) 929-1115, Toll Free (800) 762-1084

TFX-FS360 User Manual

2010-07-20/14:53

OPERATING INSTRUCTIONS

Operating Modes

The TFX-FS360 can be operated in the following ways;



As a manual followspot using on-board manual controls or slaved to a DMX-512 controller for cue

changes.

As a static spot controlled by a DMX-512 controller.

Followspot Mode

Enter Manual Mode by pressing the FUNCTION SELECT button until the MANUAL LED is turned

on.

BUTTONS

DIMMER

FUNCTION

Min. and Max. buttons adjust the intensity of the light output respectively.

The electronic shutter provides instant lights on or shuts all light output off for a

blackout state.

SHUTTER

The following colors can be immediately selected by pressing each individual

button:

Color Buttons

UV, Magenta, Orange, Yellow, Green, Blue, red and White

FUNCTION

UP/DOWN

Press FUNCTION button to switch between manual and DMX control modes.

The Up/Down buttons are available when in DMX mode. Press the UP and

DOWN buttons to locate the DMX channel value desired.

TFX-FS360 User Manual

2010-07-20/14:53

Operating Instructions

DMX Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

customizing or creating a show. In this mode you will be able to control each individual trait of the

fixture independently.

SETTING THE STARTING ADDRESS

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,

102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate

the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping

to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that

will help you understand its use.

The TFX-FS360 utilizes two DMX control channels.

1) Press the FUNCTION button until the DMX Mode LED turns on.

2) Press the UP or DOWN buttons until the starting channel address you desire is located on the

digital display.

TFX-FS360 User Manual

2010-07-20/14:53

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user

must assign a starting address on the fixture that indicates the first channel reserved in the controller.

There are many different types of DMX controllable fixtures and they all may vary in the total number

of channels required. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

set incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).

FIXTURE LINKING

Figure 1 - DMX connector configuration

Resistance 120

ohm 1/4w between

pin 2 (DMX -) and

pin 3 (DMX +) of

the last fixture.

COMMON

DMX +

INPUT

OUTPUT

Termination reduces signal errors and to

avoid signal transmission problems and

interference, it is always advisable to connect

a DMX signal terminator.

DMX -

Note!

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin

adapter.

The chart below details a proper cable conversion:

3 PIN TO 5 PIN CONVERSION CHART

CONDUCTOR

GROUND/SHIELD

DATA ( - )SIGNAL

DATA ( + ) SIGNAL

NOT USED

3 Pin Female (output)

5 Pin Male (Input)

Pin 1

Pin 2

Pin 3

Pin 2

Pin 3

Pin 4

NOT USED

Pin 5

TFX-FS360 User Manual

2010-07-20/14:53

Appendix

DMX Channel Values

Channel

Value

Function

Color Wheel

Open

Red

Blue

Green

000  031

032  063

064  095

096  127

128  159

160  191

191  223

224  255

Yellow

Orange

Magenta

UV (Purple)

Dimmer

000  004

005  249

250  255

No Output

Closed > Open

Full Output (100%)

Gobos

Maintenance

To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage

and environment are contributing factors in determining frequency. As a general rule, fixtures should

be cleaned at least twice a month. Dust build up reduces light output performance and can cause

overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off

fixture before conducting maintenance.

Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust

collected on external vents and internal components. Clean all glass when the fixture is cold with a

mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply

solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical

surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil

and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or

becomes dirty, clean the lamps with an alcohol wipe.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates:

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s

optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean

the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.

Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).

Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to

shipping the fixture. Be prepared to provide the model number, serial number and a brief description

of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from

inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own

discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is

always a safe method to use.

TFX-FS360 User Manual

2010-07-20/14:53

Appendix

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be

reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and

submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim

for items such as missing component/part, damage not related to shipping, and concealed damage,

must be made within seven (7) days of receiving merchandise.

General Troubleshooting

Applies to

Foggers

& Snow

Dimmers

& Chaser

Symptom

Solution(s)

Lights

Controllers

Auto shut off

Check fan thermal switch reset

Clean optical system or replace lamp



Beam is very dim or not

bright



Breaker/Fuse keeps

blowing

Check total load placed on device



Chase is too slow

Check users manual for speed adjustment



Device has no power

Check for power on Mains.



Check device’s fuse. (internal and/or external)

Fixture is not responding

Check DMX Dip switch settings for correct addressing

Check DMX cables



Check polarity switch settings

Lamps cuts off

sporadically

Possible bad lamp or fixture is overheating.

Lamp may be at end of its life.

Light will not come on after

power failure

Some discharge lamps require a cooling off period before the

electronics in the fixture can kick start it again, wait 5 to 10 minutes

before powering up

Loss of signal

Use only DMX cables



Install terminator

Note: Keep DMX cables separated from power cables or black lights.

Motor movements are

jerky or jumpy

Possible bad motor driver or sensors

Check polarity switch on controller



No flash

Re-install bulb, may have shifted in shipping

No light output

Check slip ring & brushes for contact

Install bulb



Call service technician

TFX-FS360 User Manual

2010-07-20/14:53

Appendix

Technical Specifications

WEIGHT & DIMENSIONS

Length....................................................................................................................... 572 mm (22.5 in)

Width......................................................................................................................... 292 mm (11.5 in)

Height ....................................................................................................................... 162 mm (6.38 in)

Weight........................................................................................................................ 9.3 kg (20.6 lbs)

POWER

US.................................................................................................................................... 120 V, 60 Hz

European Version ............................................................................................................ 230 V, 50 Hz

AC input.......................................................................................3-prong IEC 60320 C14 male socket

LIGHT SOURCE

Lamp............................................................................................................. ENX, 360 W, 82 V, 75 hr,

PHOTO OPTIC

Luminance @ 1 m................................................................................................................ 48,420 lux

Beam Angle .............................................................................................................................2° ~ 12°

THERMAL

Maximum ambient temperature......................................................................................40° C (104° F)

CIRCUIT BREAKER

Main @ 120 V ................................................................................................................................. 7 A

Main @ 230 V ................................................................................................................................. 5 A

CONTROL & PROGRAMMING

Data input ............................................................................................. locking 3-pin XLR male socket

Data output ........................................................................................ locking 3-pin XLR female socket

Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)

Protocols.....................................................................................................................DMX-512 USITT

DMX Channels....................................................................................................................................2

ORDERING INFORMATION

Followspot™ 400G............................................................................................................. TFX-FS360

Tripod Stand with Casters (optional)........................................................................................ CH-W28

GOBO

Outside diameter.....................................................................................................................35.8 mm

Image diameter.......................................................................................................................27.9 mm

Maximum thickness...................................................................................................................0.2 mm

TFX-FS360 User Manual

2010-07-20/14:53

Black Box Computer Accessories gigatrue cat6 component level patch panels User Manual
Blaupunkt Car Stereo System RPD 552 User Manual
Bowers Wilkins Speaker 2 SE User Manual
Braun Iron 4 695 User Manual
Briggs Stratton Lawn Mower MODEL 290000 User Manual
Broil King Gas Grill 9986 44 User Manual
Brother Printer 9200DX User Manual
Bryant Furnace 359AAV User Manual
Casio Time Clock MA0309 EA User Manual
CAT Portable Generator GT950 User Manual